- 1 Can you lay decking over concrete?
- 2 How low can a deck be to the ground?
- 3 Can you screw decking straight to concrete?
- 4 What do you put under decking?
- 5 What can I cover my concrete patio with?
- 6 Can you cover concrete porch with wood?
- 7 How do you attach wood to concrete?
- 8 What do you put under ground level deck?
- 9 How do you lay decking on uneven ground?
- 10 Can you make a deck out of 2×4?
- 11 What is a floating deck?
- 12 Can you put Trex over concrete?
- 13 How do you attach deck boards to concrete?
Can you lay decking over concrete?
Even if your patio is in terrible shape, you can deck over it. Cracks, craters and seasonal movement along cracks are no problem. (depending on the thickness of your decking and whether or not you put spacers under the sleepers). So any door thresholds adjoining the patio must be at least that far above the concrete.
How low can a deck be to the ground?
There is no standard height for a “grade-level” deck—the maximum measurement from grade to the deck surface could be 6 inches, 12 inches, 24 inches, or more. But generally speaking, I apply the term to decks that are up to 30 inches above grade, since guardrails are required for any decks that are higher than that.
Can you screw decking straight to concrete?
Yes, you can lay or install composite decking on concrete if your want to.
What do you put under decking?
If you‘re laying your deck straight onto the ground, cover the area with a layer of weed control fabric. Then add 40 mm to 50 mm of gravel on top. The other method is to create concrete pads for the deck to sit on top of. This will reduce the likelihood of moisture seeping into the frame and causing damage.
What can I cover my concrete patio with?
You can‘t turn back time on spalling or cracks, but you can cover them up with the right concrete repair products. For example, a layer of Quikrete’s Re-Cap Concrete Resurfacer will give your patio a smooth and wear-resistant finish with the look of freshly poured concrete, but with a shorter working and wait time.
Can you cover concrete porch with wood?
Covering your concrete porch with wood provides a warmer feel. Covering a concrete porch with wood provides a warmer, cozier feel. It is also a good way to cover up peeling paint, slight chipping and discolored concrete. Whatever your reasons, adding a wood floor to your concrete porch is a fairly simple operation.
How do you attach wood to concrete?
The fastest and easiest way to attach most wood parts to concrete is to use a powder-actuated gun. To use it, load a special gun nail and a. 22 caliber gun shell into the barrel. Press the nose against the workpiece, pull the trigger and the shell will drive the fastener directly into the concrete.
What do you put under ground level deck?
If the bottom of your deck frame is less than 6″ above the ground or partially buried, you should use pressure-treated wood that is rated for ground contact. This type of wood has a higher level of preservative that guards the wood against rot and decay.
How do you lay decking on uneven ground?
To build a decking base on sloped uneven ground:
- Clear the area of all grass, weeds and debris using a good quality spade.
- Dig 1ft deep post holes.
- Set the posts using post mix so that the top is at or slightly above the desired height.
Can you make a deck out of 2×4?
For the deck surface, you can use 2x4s, 2x6s, or 5/4x6s. The 5/4 decking (pronounced “five-quarter”), available in cedar and pressure-treated fir, is 1 inch thick and 5-1/2 inches wide with rounded edges that make for a splinter-free surface.
What is a floating deck?
A floating deck, also called a free standing deck, is simply a deck that’s not attached to any structure, including (of course) your house. To understand how to build a floating deck, here are a few basics. As an independent structure, a floating deck has a few advantages over an attached deck.
Can you put Trex over concrete?
Some may be wondering, “Can you lay Trex composite decking over concrete?” Yes!
How do you attach deck boards to concrete?
Use a wood bit to drill ½” pilot holes through the ledger board. Next, use a concrete bit to drill into the concrete wall. Install two bolts at the end of each ledger board. Hammer the sleeve anchor through the ledger board into the concrete wall.