- 1 Can I pour my own concrete patio?
- 2 How do you prepare the ground for a concrete patio?
- 3 How much does a 12×12 concrete patio cost?
- 4 Can concrete be poured directly on dirt?
- 5 Do you need gravel under concrete?
- 6 What is the cheapest way to pour a concrete slab?
- 7 Is sand a good base for concrete?
- 8 What is the best base for concrete slab?
- 9 Do you need rebar for 4 inch slab?
- 10 How much does a 10×20 concrete patio cost?
- 11 How much does a 20×20 stamped concrete patio cost?
- 12 How many bags of concrete do I need for a 10×20 slab?
- 13 Should you put plastic under concrete?
- 14 How long does it take for 4 inches of concrete to cure?
- 15 How many inches of gravel do you need for a concrete slab?
Can I pour my own concrete patio?
You’ll save 40 percent to 50 percent by pouring your patio yourself. (Taking the DIY route also means you can be sure the technical details are done correctly.) You’ll save even more if you mix your own concrete instead of having a ready-mix truck deliver it.
How do you prepare the ground for a concrete patio?
Preparation is the most important aspect of pouring a concrete slab.
- Dig the ground down to the proper depth.
- Smooth out the ground with the flat side of a rake so that you have a level surface.
- Tamp the ground with a hand tamper or mechanical tamper.
- Pour 2 inches of small, rounded gravel for additional drainage needs.
How much does a 12×12 concrete patio cost?
Cost to Install Concrete Patio by Size
|Size in Feet||Square Footage||Price Range|
|10×10||100||$900 – $2,600|
|12×12||144||$1,200 – $3,000|
|12×14||168||$1,400 – $4,000|
|15×15||225||$1,800 – $5,500|
Can concrete be poured directly on dirt?
Long story short, yes you can pour concrete over dirt.
Do you need gravel under concrete?
Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.
What is the cheapest way to pour a concrete slab?
One of the least expensive ways to get concrete is to mix your own. You can buy bags of the mix from a home improvement store. Typically, you only have to add water for it to be ready to pour. However, it is important to get the ratio right and to mix the concrete thoroughly.
Is sand a good base for concrete?
Pour concrete over a solid, well-drained base
of sand or gravel over clay and other poorly draining soils to provide even support.
What is the best base for concrete slab?
Most concrete contractors want a mix of coarse and fine aggregate to create a compactable base that is going to be safe for settlement and drainage. Crusher run (a mix of crushed stone and stone dust) is one of the best base materials for concrete flatwork.
Do you need rebar for 4 inch slab?
No, you do not need rebar for a 4–inch slab of concrete on grade. A 4–inch-thick slab cast on the ground and in permanent contact with it will float and rebar is not required. Rebar is recommended on concrete measuring 5 – 6 inches thick.
How much does a 10×20 concrete patio cost?
Cost of concrete per square foot
|Slab Size||Square Feet||Average Cost|
How much does a 20×20 stamped concrete patio cost?
The average cost for a stamped concrete is $5 to $12 per square foot, not including the concrete slab which costs $2 – $7 per square foot. Most homeowners spend a total of between $3,751 – $8,540 for stamped concrete patio. Get free estimates from concrete pros near you.
How many bags of concrete do I need for a 10×20 slab?
A 60-pound bag yields. 017 cubic yards, and an 80-pound bag yields. 022 cubic yards. For a 10 x 10 slab, you would need 77 60-pound bags or 60 80-pound bags.
Should you put plastic under concrete?
Recently, though, research has shown that the old traditional layer of 6-mil Visqueen (polyethylene plastic) under the slab is seldom effective for two main reasons: Although it may seem water-tight, this grade of material allows a lot of water vapor to pass through.
How long does it take for 4 inches of concrete to cure?
When waiting for concrete to dry, keep these timeframes in mind: 24 to 48 hours – after inital set, forms can be removed and people can walk on the surface. 7 days – after partial curing, traffic from vehicles and equipment is okay. 28 days – at this point, the concrete should be fully cured.
How many inches of gravel do you need for a concrete slab?
Excavate the slab area to a depth of about 7 inches, allowing 3 inches for a gravel base and 4 inches for concrete.