Often asked: How Much To Rent A Concrete Saw?

Does Home Depot rent concrete saws?

Let The Home Depot Tool Rental Centers handle all your cutting and concrete rental equipment needs. We offer concrete mixer rentals and saw rentals, including concrete saws, masonry saws, miter saws, tile saws and gas chainsaws from our selection of trusted professional-quality top brands.

How deep will a 12 inch concrete saw cut?

Cured Concrete/Asphalt Blades
Diameter Cutting Depth*
12 (305mm) 4″
14″ (356mm) 5″
18″ (457mm) 7″

How fast does a walk behind concrete saw cut?

Cutting is done dry with the green concrete saws. Like regular concrete saws, these saws range in size and in- tended use. Blade speed is fast, usually between 5,400 and 5,800 rpm.

How deep will a 14 concrete saw cut?

A 14-inch circular blade on a cut-off saw is designed for a maximum depth of slightly less than five inches.

You might be interested:  Often asked: How To Stop Water Leaks In Concrete Walls?

Should I rent a concrete mixer?

If you use 60-pound bags, concrete for a patio this size ranges from $135 to $180. But you’ll need to rent a mixer, which adds another $40 to $60 per day. While ready-mix reduces work, it also boosts the cost. It’s a small price to pay for a job that can be finished in a day, and to avoid a concrete project gone bad.

How much is it to rent a drill from Home Depot?

home depot tools rental price list | Drills & Hammers

home depot rental price list | Drills and Hammers hourly daily
Drill 3/4″ (Electric) $4 $23
Drill 1/2″ right angle (Electric) $4 $23
Roto Hammer 7/8″ (Electric) $6 $35
Breaker – Small $9 $50

How deep can you cut concrete?

Depth of Cut

As far as the depth of the cut is concerned, professionals recommend cuts ranging from one quarter to one third of the thickness of the slab. Simply put, this means that the cutting depth should be restricted to around 2.5 inches for an 8 inch thick concrete slab.

Who makes the best concrete saw?

Quick Look: Our Top Concrete Saws

Product Price
TOP RATEDHusqvarna Husqvarna 967181002 K760 II 14-inch Gas Cut-Off Saw Price not available
Hilti DSH 700 14″ Hand Held Gas Saw – 385636 $1,599.61
Makita EK6101 14-Inch 61 CC Power Cutter $952.56
BEST BUDGET PICKEvolution DISCCUT1 12-Inch Disc Cutter, Orange $202.79

How close can a concrete saw cut to a wall?

How close can you slab saw perpendicular to a wall? The slab saw blade-guard needs approximately 3” clearance from the wall.

You might be interested:  Question: How To Repair Concrete Walkway?

How do you cut a 4 inch concrete slab?

Use a standard circular saw, equipped with a corundum or diamond blade, for small tasks. For slabs, it’s best to cut through the top inch, then use a sledgehammer to break off the rest. The jagged edge left below the cutting line provides a good rough edge for the new concrete to bond to.

Do you push or pull a concrete saw?

Always let the saw do the work; simply guide its direction, but don’t push it down into the concrete. You only need a quarter-inch cut at this point, but if the saw bites in a bit deeper, that’s fine too. This first guided cut will ensure you keep your cuts straight during the rest of the project.

What is the best blade for cutting concrete?

Diamond saw blades are typically the best choice when it comes to making clean, professional cuts in concrete.

When should you cut concrete?

Joints should be sawed as soon as the concrete will withstand the energy of sawing without raveling or dislodging aggregate particles. For most concrete mixtures, this means sawing should be completed within the first six to 18 hours and never delayed more than 24 hours.

Do concrete saws cut rebar?

Rebar provides a strong net that the concrete sets around. Major cutting of concrete should be left to the professionals, but a minor job around the home can be done with the right equipment. Many home improvement stores rent concrete wet cutters with diamond blades, which are needed for cutting through the rebar.

You might be interested:  How To Repair Cracked Concrete Floor?

How do you cut concrete by hand?

Cutting Concrete With Hands

  1. Mark the Cut Area. Use a pencil to draw the area that will be cut away from the concrete.
  2. Use a Hammer and Chisel. In one hand, take a chisel and place the edge at one end of the mark in the concrete.
  3. Use an Angle Grinder. After creating the groove, use an angle grinder to begin cutting into the groove along the mark.

Leave a Reply

Your email address will not be published. Required fields are marked *