- 1 How much does it cost to pour a 12×12 concrete slab?
- 2 Can I pour my own concrete slab?
- 3 How deep does a concrete pad need to be?
- 4 Can you pour concrete directly on dirt?
- 5 Is it cheaper to buy premixed concrete?
- 6 Is it cheaper to do pavers or concrete?
- 7 Do you need gravel under concrete?
- 8 Is it cheaper to make your own concrete?
- 9 Do you need rebar for 4-inch slab?
- 10 Can I pour a 2 inch concrete slab?
- 11 How many bags of concrete do I need for a 10×10 slab?
- 12 How strong is 2 inches of concrete?
- 13 Should I put plastic under concrete?
- 14 How do you prepare the ground before pouring concrete?
- 15 Is sand a good base for concrete?
How much does it cost to pour a 12×12 concrete slab?
How much does a 12×12 concrete slab cost? The average cost to pour a 12×12 concrete slab that is 4” thick is between $888 and $1,584, with professional labor and materials included.
Can I pour my own concrete slab?
Used for walkways, patios, and floors, concrete slabs are inexpensive to install and durable enough to last for years. When you pour your own concrete slab, you’re giving yourself a design material that is adaptive to all of your needs.
How deep does a concrete pad need to be?
Standard concrete floor slab thickness in residential construction is 4 inches. Five to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks. To prepare the base, cut the ground level to the proper depth to allow for the slab thickness.
Can you pour concrete directly on dirt?
Long story short, yes you can pour concrete over dirt.
Is it cheaper to buy premixed concrete?
It’s cheaper to do all the prep and buy the concrete premixed and delivered. For example, a 10×20′ slab of 4″ concrete would be a minimum of 2.5-3 yards. Here concrete is about $80/yard (closer to $70), or $240 for the concrete. That same slab would take 223 40-pound bags, or 112 80-pound bags.
Is it cheaper to do pavers or concrete?
As far as installation costs and concrete costs go, poured concrete is technically the most affordable per square foot. However, even though the upfront cost of pavers is higher, concrete pavers offer greater value and durability than poured concrete and stamped concrete.
Do you need gravel under concrete?
Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.
Is it cheaper to make your own concrete?
One of the least expensive ways to get concrete is to mix your own. You can buy bags of the mix from a home improvement store. Typically, you only have to add water for it to be ready to pour. Otherwise, you risk getting a weaker concrete once it cures, which could lead to cracks or crumbles within a couple of years.
Do you need rebar for 4-inch slab?
No, you do not need rebar for a 4–inch slab of concrete on grade. A 4–inch-thick slab cast on the ground and in permanent contact with it will float and rebar is not required. Rebar is recommended on concrete measuring 5 – 6 inches thick.
Can I pour a 2 inch concrete slab?
If done properly, new concrete can often be poured right over an existing slab. For this to be feasible, the contractor needs to pour at least 2 inches thick, use smaller aggregate, and incorporate reinforcement such as welded wire mesh or fiber mixed into the concrete.
How many bags of concrete do I need for a 10×10 slab?
For a 10 x 10 slab, you would need 77 60-pound bags or 60 80-pound bags. If we add an extra 10%, that’s an extra 8 60-pound bags or 6 80-pound bags.
How strong is 2 inches of concrete?
How strong is 2 inches of concrete? A common bag of concrete, for example, may have a compression strength of 4,000 psi, based on a thickness of 2 inches after it has set for 28 days. Other concrete may have a compression strength of only 550 psi.
Should I put plastic under concrete?
Recently, though, research has shown that the old traditional layer of 6-mil Visqueen (polyethylene plastic) under the slab is seldom effective for two main reasons: Although it may seem water-tight, this grade of material allows a lot of water vapor to pass through.
How do you prepare the ground before pouring concrete?
Preparation is the most important aspect of pouring a concrete slab.
- Dig the ground down to the proper depth.
- Smooth out the ground with the flat side of a rake so that you have a level surface.
- Tamp the ground with a hand tamper or mechanical tamper.
- Pour 2 inches of small, rounded gravel for additional drainage needs.
Is sand a good base for concrete?
Pour concrete over a solid, well-drained base
of sand or gravel over clay and other poorly draining soils to provide even support.