Often asked: How To Resurface A Concrete Floor?

Can old concrete be resurfaced?

Concrete resurfacing is a way to make damaged or dated concrete look new again. A concrete coating is applied over the old surface, offering a variety of color, texture and pattern options. This type of decorative refinishing can be done on driveways, patios, pool decks and even indoor floors.

How much does it cost to resurface a concrete floor?

The average cost to resurface 100 square feet of concrete is $400. Less expensive projects can run as little as $300 while more expensive ones are about $500. The price per square foot can range between $3 and $5. The resurfaced area could be a driveway, patio, pool deck, floor or slab foundation in the basement.

Does concrete resurfacing last?

How long does it last? Thanks to its advanced bonding properties, concrete resurfacing can last for quite a while. A properly resurfaced floor can last from 8-15 years.

How do you make concrete look new again?

3 Ways to Make Old Concrete Look New Again

  1. Power Wash. Over time, your concrete will accumulate grime and dirt.
  2. Resurface. If you’re looking for a quick and easy way to improve your curb appeal, resurfacing your concrete steps and driveway is a great way to start.
  3. Add Stain or Sealing Coats.
  4. Revive Your Old Concrete.
You might be interested:  Often asked: How Remove Oil Stains From Concrete?

Can you put a thin layer of concrete over concrete?

Yes, you may pour a concrete pad overlay over an existing slab. You need to consider the added height and weight of the overlay on the existing structure. Overlays may include polymers, portland cement concrete, or epoxies.

Can crumbling concrete be repaired?

The Cure for Crumbling Concrete Steps



As long as the steps are structurally sound—meaning, they’re not spalling, flaking, or broken all the way through—you can repair most surface issues. If your patch is thicker, build the vinyl concrete patcher up in ¼ inch applications.

Can you pour new concrete over old cracked concrete?

There are situations when pouring new concrete isn’t the most suitable option. For instance, surfaces with larger cracks, heaving or settling conditions, or where height cannot be raised, replacement is a better solution. However, in most cases, you can pour a new layer of concrete onto the existing one.

What is the best product to resurface concrete?

QUIKRETE® Concrete Resurfacer is a special blend of Portland cement, sand, polymer modifiers and other additives designed to provide a shrinkage compensated repair material for making thin repairs to sound concrete which is in need of surface renewal.

What is the best concrete overlay?

Broom Finish Concrete Overlay



SureBroom is our strongest overlay, has the largest aggregate, and is suited for the highest wear surface including vehicular and foot traffic. Trowel or spray applications.

Can pitted concrete be resurfaced?

Indeed, you can use resurfacer to revive just about any worn-out concrete surface. In especially dry, windy, or hot conditions, it may be necessary to mist the area while the resurfacer gains strength.

You might be interested:  How Much Does It Cost To Build A Concrete Driveway?

Should I resurface my concrete driveway?

Enhances your driveway’s appearance: one of the best values of concrete driveway resurfacing is it improves your driveway’s appearance. The new layer gives your driveway a fresh look after years of fading and cracking. Extends its lifespan: if you care for your driveway correctly, it should last for up to thirty years.

Does bleach destroy concrete?

Bleach is safe to use on concrete. When applied to concrete, bleach does not harm the sturdy material. However, it does remove spots and unwanted matter from the surface, such as mildew and moss. It also disinfects concrete.

Is Power Washing bad for concrete?

The quick answer is yes, power washing can degrade a concrete surface. The top reasons for pressure washing damage are using the wrong nozzle, excessive pressure, spraying too close to a concrete surface and holding the nozzle on a particular spot for too long.

Leave a Reply

Your email address will not be published. Required fields are marked *