Quick Answer: How Much Concrete For 10 Sonotube?

How many bags of concrete does it take to fill a sonotube?

16 cubic feet / 0.6 cubic feet / per bag = 27 (80#) bags of concrete mix.

How much concrete do I need calculator?

For concrete, the formula for volume is as follows: length x width x thickness. To determine how many bags of concrete you will need, divide the total cubic yards needed by the yield. Use the following yields per each bag size: 40 pound bag yields.011 cubic yards.

How deep should Sonotubes be?

Brace securely at top, middle and bottom of tube. There is no pour rate restriction below the joint, but you CANNOT pour a full liquid head up to 20 feet when using a “Joined” Finish Free Tube if the joint is below the 20 foot level.

You might be interested:  Readers ask: How To Remove Concrete Stain From Brick?

How do you calculate concrete for a round hole?

The formula for the volume of a round hole is pi r2 x depth. Or 3.14 x radius x radius x depth. The radius is half the width of the hole.

How many bags of concrete do I need for a 4×4 post?

Mix two 50lb bags of concrete with water in a mixing tub or 5-gallon bucket. Add concrete into the hole and around the 4” x 4”. Depending on your climate, let concrete set up for 24 – 48 hours.

How many 80lb bags of concrete makes a yard?

If you’re using 80lb bags of concrete, you’ll need 45 bags to make a yard.

How many bags of concrete do I need for a 10×20 slab?

A 60-pound bag yields. 017 cubic yards, and an 80-pound bag yields. 022 cubic yards. For a 10 x 10 slab, you would need 77 60-pound bags or 60 80-pound bags.

How much sand and cement do I need for 1 cubic meter of concrete?

Thus, the quantity of cement required for 1 cubic meter of concrete = 0.98/0.1345 = 7.29 bags of cement. The quantities of materials for 1 m3 of concrete production can be calculated as follows: The weight of cement required = 7.29 x 50 = 364.5 kg. Weight of fine aggregate (sand) = 1.5 x 364.5 = 546.75 kg.

How do you calculate concrete meters?

Calculating Cubic Metres



If you took metric measurements, then multiply the length by the width by the depth (L x W x D) to find the volume needed in cubic metres. For measurements in centimetres, multiple the measurements by 100 to find the amount in metres.

You might be interested:  What Is A Concrete And Abstract Nouns?

Do you leave sonotube in ground?

No, it’s not a problem to leave the Sonotube and its plastic “Square Foot” (like these) in the ground forever.

How many posts do I need for a 12×16 deck?

A standard deck will need four footings parallel to the house, but they will need to be temporarily braced by 6 inch-by-6 inch posts.

How many bags of concrete do I need for a 6×6 post?

As I recall, a 60# bag of concrete is about. 5cf, so you’d need 3 bags per hole.

How many 20kg bags of premixed concrete do you need?

For jobs where a stronger rated concrete is needed, youmay consider our High Strength Concrete Mix for your concreting purposes. Yield: One 20kg bag will cover an area of 1.1m2 to a depth of approximately 10mm. Or 108 x 20kg bags equates to one cubic metre of mixed concrete.

How much does it cost for 10 yards of concrete?

The average cost of concrete delivery is $119 to $147 per cubic yard for a full 10-yard truckload of ready-mix concrete, and $172 per yard for a short-load of less than 10 yards.

Leave a Reply

Your email address will not be published. Required fields are marked *