- 1 How do you set a concrete level post?
- 2 How do you keep fence post levels in concrete?
- 3 How do you level posts on uneven ground?
- 4 Can pressure treated posts be set in concrete?
- 5 Is 2 feet deep enough for fence posts?
- 6 How many bags of concrete do I need for a 4×4 fence post?
- 7 How do I put a post in the ground without concrete?
- 8 How long will a treated 6×6 post last in the ground?
- 9 How do you level post height?
- 10 How big of a hole do I need for a 6×6 post?
- 11 How deep should a 6×6 post be in the ground?
- 12 Does filling a post with concrete make it stronger?
How do you set a concrete level post?
- Dig the post hole, making it three times the width of the post and at a depth equal to 1/3 to 1⁄2 of the above-ground length of the post, plus 6″ (right).
- Pour 6″ of gravel or crushed stone into the bottom of the hole.
- Set the post in the hole.
How do you keep fence post levels in concrete?
Setting the Post
You need to level it in two directions with a 4-foot level. After getting it straight in the first direction, hold one of the braces against the post and drive a single screw to connect the brace to the post. You can then level and brace the post in the other direction and begin filling the hole.
How do you level posts on uneven ground?
Once your posts are set in concrete, you will figure out where the top of your fence will be on the posts. The easiest way to do this is to find the lowest height post and then mark the other posts to be cut down to that level. Mark where you need to cut with a pencil. Now you can install your fence.
Can pressure treated posts be set in concrete?
Simply setting the posts in concrete does create a condition that will accelerate rot in the bottom of the posts. With pressure–treated posts, the rot will be slow. Concrete should be poured around the post – no concrete under the post.
Is 2 feet deep enough for fence posts?
The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).
How many bags of concrete do I need for a 4×4 fence post?
Mix two 50lb bags of concrete with water in a mixing tub or 5-gallon bucket. Add concrete into the hole and around the 4” x 4”. Depending on your climate, let concrete set up for 24 – 48 hours.
How do I put a post in the ground without concrete?
- Find a concrete surface and lightly tamp your digging iron against it.
- Remove the turf and topsoil from the site of the post.
- Dig the hole putting the displaced earth onto the tarp.
- Pour 4 inches of gravel into the hole.
- Place the post in the hole.
- Add another 2 inches of gravel around the base of the post.
How long will a treated 6×6 post last in the ground?
The treated post that are rated for ground contact are guaranteed for 40 years.
How do you level post height?
To get a level line for the top of the posts, temporarily install a nail at the top of each terminal post (if setting the end posts first) or at a mark on the side if doing all 8 at once. Make sure the string is set-up the same way on each terminal post. An inexpensive post & string level should cost around $10.
How big of a hole do I need for a 6×6 post?
A 6×6 post requires a 10″-diameter hole. Shovel a 6″ layer of gravel into the hole to provide drainage.
How deep should a 6×6 post be in the ground?
In general, holes should be at least 3 feet deep for posts that extend 8 feet or more above ground level. Posts that extend 6 feet above ground level should have holes at least 2 1/2 feet deep.
Does filling a post with concrete make it stronger?
Filling with concrete is not as effective as increasing wall thickness or changing the shape, but it’s a proven technique.